Exhibitors

Capacity Range: From 100 m³/h to 700.000 m³/h flow rate Pressure Range: from 10 mmWC to 3500 mmWC pressure Centrifugal fan is defined as a mechanical device that moves air or other gases. Centrifugal fans increase the air/gas flow volume by using the kinetic energy of the impellers. In turn, it moves the air against the resistance caused by ducts, valves, and other components. Centrifugal fans displace the air radially and change the direction of the airflow by 90° degrees. They are durable, quiet, reliable, and capable of operating in a wide variety of conditions. Industrial Type Centrifugal Fans: Low, medium, and high pressured fans, boiler fans, flue fans, circulation fans, paint shop exhaust fans, acoustically/thermally insulated fans, hood fans, roof fans, plug fans, filter aspirators, pneumatic conveying fans, chopper fans with cutting blades, wear resistant fans, heat resistant fans, custom fans. Industrial Type Centrifugal Fans: Can be produced as standard bladed and multibladed. According to Drive System: Direct Drive Direct Drive with Coupling Belt Drive According to production materials: Carbon steel (St 37/2, St52/3 etc.) Stainless steel (AISI 304/316/321/309/310) Aluminum, brass Our Accessory Portfolio: Valves (drallregler, butterfly, slider, volumetric damper). Manual, piston, actuator, reducer types. Silencers, (square and round types). Body insulations (fiberglass, rock wool, ceramic wool, etc.) Sensors (temperature, vibration, revolution, pressure, etc.) Special sealing equipment, Standard and special type compensators.

From 100 m³/h to 150.000 m³/h flow Pressure Range: from 5 mmSS to 130 mmSS pressure Axial fans are types of compressors that increases the pressure of the air passing through it. The blades of axial flow fans force air to move parallel to the line in which the blades rotate. In other words, the flow is axially in line with the shaft whroughout the whole fan. Axial fans are often used for ventilation in processes. In addition, project-based custom production axial fans are also manufactured. Industrial type axial fans: wall type, duct type, roof type, ventilating fans, hot air exhaust fans, cooling fans, steam exhaust fans, shell cooling fans, special type fans to operate at high temperatures, fans for special projects. Industrial type axial fans: can be manufactured with different blade numbers and profiles based on flow and pressure variables. According to drive system: Direct Drive Direct Drive with Coupling Belt Drive According to production materials: Carbon steel (St 37/2, St 52/3 etc.) Stainless steel (AISI304/316/321/309/310) Aluminum casting. Our accessory portfolio: Valves (Volumetric damper) Silencers (Square and round types) Body insulations (fiber glass, rock wool, ceramic wool, etc.) Sensors (Temperature, vibration, speed, pressure, etc.) Standard and special-type compensators.

From 100 m³/h to 300,000 m³/h flow rate Pressure Range: from 10 mmSS to 200 mmSS pressure Mixed flow fans are positioned between centrifugal and axial fans in terms of performance and design. Especially in systems with high volumetric flow and high pressure loss, such industrial fans are an important part of the process. Centrifugal fans provide low flow and high pressure difference, while axial fans provide high flow and low pressure increase. Mixed flow fans are flow machines designed for both high pressure and high flow requirements. Industrial Type Mixed Flow Fans: They are widely used in many areas of industry. Applications involving smoke, spray painting booth, flows containing particles, flows containing excessive moisture or high temperature are several examples for these industrial applications. Drive Type: Direct Drive Direct Drive with Coupling Belt Drive Production Materials: Carbon steel (St 37/2, St52/3 etc.) Stainless steel (AISI 304/316/321/309/310) Aluminum, brass. Our accessory portfolio: Valves (Drallregler, butterfly, slider, volumetric damper) Manual, piston, actuator, reducer types Silencers, (Square and round types) Body insulations (fiber glass, rock wool, ceramic wool, etc.) Sensors (Temperature, vibration, speed, pressure, etc.) Special sealing equipment Standard and special-type compensators.

Jet filters with a filtration surface area of ​​5 m² - 7000 m² are designed and produced within our company. Jet pulse filter is an air pollution control device that separates particulate matter from air or gas. Filter bags made of polyester felt are used as filtering elements. System elements consist of screw conveyor, airlock, and centrifugal fan. It can be used with the cyclone unit depending on the system requirement. Jet filter unit works with 6 7 bar air pressure. Compressed air entering the system vibrates via a solenoid pulse valve with a remote electronic control card and ensures the cleaning of the filter elements. Filter design criteria is designed and projected depending on the: Dust type, Dust load, Physical and chemical properties of the dust Moisture or abrasiveness Industrial-type dry filtering elements are produced as bag or cartridge models. Filtering element is selected according to the requirements of the process. Industrial-type dry filters: Central system dust collection units Central and mobile type vacuum units Silo-Top Filters Dryer Type Filters Mill Filters Product Filters Boiler Flue Filters Process Filters Filters suitable for special projects Pulsing System: On-Line Pulsing Off-Line Pulsing Designed Model: With Hopper With Pre-Separation Silo-Top Filter Without Hopper Double Module High Pressure Cylindrical According to the production material: Carbon steel (St 37/2, St 52/3 etc.) Stainless steel (AISI304/316/321/309/310). Our accessory portfolio: Screws Conveyors Air Locks Air Slide Conveyors Weighted Valves Pendel Valves Slide Valves

Capacity Range: 1000 m³/h to 50.000 m³/h flow rate Wet Scrubbers, which are another type of dust collection unit, are effectively used in processes where there is a risk of dust and gas mixture and spark in a humid environment. As a result, it is a process which collects the particles with the intense interaction of sucked air with water. The part that ensures the correct operation of the system in the product is the pump Wet scrubbers are mainly used in the following areas. Chemical plants Ceramic factories Galvanizing plants Marble processing plants The wastes kept in the system are transferred to a pool. This pool can be in-house or can be manufactured separately. If there is a purification system in the facility; the wastes settle and the process ends. Depending on design, can be designed with or without a pump. Manufacturing materials options are, carbon steel (St37/2, St 53/2, etc.), stainless steel (AISI 304/310) Depending on the type of process, the body can be manufactured as rectangular or cylindrical Accesories: plastic separator, raschig rings.

The company designs and manufactures mobile type cleaning units with flow rate of 100 m3/h - 500m3/h within its own organisation. Jet type pulse filters are air pollution control devices that separate particulate matters from the air or gas. Filter cloths made of felt are used as filter components. System components are comprised of a screw conveyor, air lock and centrifugal fan. Depending on the system requirement, they may be used together with the cyclone unit. Jet filter unit operates at an air pressure of 6 7 bars. Compressed air entering the system achieves vibration via an electronic remote control card with a solenoid impact valve and ensures the filter components to be cleaned. Industrial Mobile Type Cleaning Units: manufactured in bag type. Filter components are selected on the basis of the process requirements. By pulsing system: sequential pulsing. By design: high pressure cylindrical. By production material: Carbon steel (St 37/2, St 52/3, etc.), stainless steel (AISI304/316/321/309/310). Our accessory range: dust bins, air locks, air slide conveyor, weighted valves, pendulum valves, slide valves.

The company designs and manufactures central vacuum cleaner units with a flow rate of 100 m3/h - 5000 m3/h within its own organisation. Jet type pulse filters are air pollution control devices that separate particulate matters from the air or gas. Filter cloths made of felt are used as filter components. System components are comprised of a screw conveyor, air lock and centrifugal fan. Depending on the system requirement, they may be used together with the cyclone unit. Jet filter unit operates at an air pressure of 6 7 bars. Compressed air entering the system achieves vibration via an electronic remote control card with a solenoid impact valve and ensures the filter components to be cleaned. Centralised System Industrial Vacuum-Cleaner: manufactured in bag type. Filter components are selected on the basis of the process requirements. By pulsing system: on-line pulsing, cell pulsing. By design: bunker inlet, front settling reservoir, silo-top bunker-free, double module, high pressure cylindrical. By production material: Carbon steel (St 37/2, St 52/3, etc.), stainless steel (AISI304/316/321/309/310). Our accessory range: screw conveyors, air locks, air belts, weighted valves, pendulum valves, slide valves.

Capacity Range: From 550 m³/h to 66.000 m³/h flow rate Being included in the category of industrial dust collectors, the cyclones are used directly or before the jet filter to collect solid particles. Cyclones operate on the dust separation principle, after a cyclonic movement at the inlet. Air lock and weighted cover can be counted as equipment of the unit. The cyclone collects coarse-grained materials based on their structure, as fine materials in dusty air can be removed outside. If this value is within acceptable limits, the cyclone itself can be used as a dust collector. Cyclones can be produced in different designs according to the characteristics and efficiency of the dusts. Cyclones can be produced as horizontal or vertical cyclones. Under current conditions, vertical cyclones are the most preferred models. The criterion that determines the cyclone size is the air flow rate sucked in. Cyclones that are not selected or produced in appropriate sizes become a problem rather than a solution. Therefore, they must be used in processes after the correct operation is ensured. Production Material: Carbon steel (St 37/2, St 52/3 etc.) Stainless steel (AISI304/316/321/309/310). According to the pressure; super cyclone, medium-pressure cyclone According to the process; they can be manufactured based on the desired capacity and its cylindrical body design. Our accessory portfolio; Screw Conveyors, Weighted Valves, Pendel Valves, Slide Valves

From 4lt/rpm to 100lt/rpm capacity Industrial type air locks; are often referred to by various names such as rotary valves, feeders, star valves. Industrial Type Air Locks; Discharge air locks under jet pulse filter, discharge air locks under cyclone, discharge air locks under silo, dosing locks, process locks, locks suitable for special projects. Production material; Cast (cast, sphero, stainless) Sheet construction (St 37/2, St 52/3, Hardox, AISI304/316/321/309/310). According to the process; They can be used as dosing and discharging elements. According to the working conditions; they are offered with different features based on their drive-type, bearings and blade tips. AIR LOCK TYPES MS19/22 ; RK25/25 and RK31/31 airlock types can be manufactured as cast iron, sphero, stainless and welded constructions. Our other models which are St37-2, Hardox as welded constructions can be manufactured from AISI quality and other materials. AIR LOCK ROTOR TYPES Open Blade Rotor Closed Blade Rotor Dosing Rotor Rubber-Tip Rotor with Open Blades

From 4 lt /rpm to 100 lt /rpm capacity Industrial-type screw conveyors can be used in various technological processes (transport, mixing, ventilation, drying, cooling, screening, washing, kneading, pressing of different bulk materials). According to the process, they are calculated, shaped, and sized. According to the production material: sheet construction (St 37/2, St 52/3, Hardox AISI304/316/321/309/310) According to the working conditions: drive type, bearings and blade tips are offered with different features.